Support Center > Search Results > SecureKnowledge Details
Required steps before installing Gaia OS on HP ProLiant Gen9 + Gen 10 servers Technical Level
Solution

Important Notes:

    • The HP ProLiant DL360/DL380 Gen9 + Gen 10 does not detect all USB devices, including different USB flash drives (regardless of content). This is not a software issue. If a bootable USB device (with Check Point's Gaia, CentOS, or any other OS) is not recognized by this server, try a different USB device vendor, or install the server through DVD.
    • Before installing Gaia OS on HP ProLiant Gen9 and Gen10 servers, make sure that Check Point supports your model, RAID controller, and network cards. To do this, see the Hardware Compatibility List.

For HP ProLiant Gen9 Servers:

  1. Do these modifications in the BIOS settings:

    Setting Feature Required modifications
    Boot Options Boot Mode
    1. Set the default to Legacy BIOS boot (to disable UEFI)
    2. Reboot
    UEFI Advanced Options
    1. Disable the UEFI
    2. Reboot
    3. Go to Storage Options
    4. Disable UEFI Array Options
    5. Reboot
    BIOS/Platform Configuration System Options - USB Options
    1. Set USB 3.0 mode to Disabled
    2. Reboot
    Process Options
    (Located in System Configuration -> BIOS/Platform Configuration (RBSU) -> Processor Options)
    1. Set HT to Disabled
    2. Set Processor X2APIC Support to Disabled
    3. Reboot
    Boot Time Optimizations
    1. Set Dynamic Power Capping function to Disabled
    2. Reboot

    Notes
    :
      • If you see a black screen in the KVM / iLO remote video (example: on HP ProLiant DL360 G9), go into ROM Based Setup Utility (RBSU) - Advanced Options - Video Options and change the setting of the embedded video connection from auto to always on.

      • If the RAID array exceeds 2TB, it might not be recognized when you install Gaia R77.30 OS. If this occurs, partition the disks as explained in sk61081. This note is applicable to R77.30, R80, and R80.10; it is not relevant to R80.20 M1. 

  2. Follow the instructions in sk98760 - Prerequisites for installing Security Management Server / Multi-Domain Security Management Server on Red Hat Enterprise Linux.

  3. It was found that BIOS version P89 v2.60 and higher, which was not certified by HCL, causes the Open Server not to reboot (warm reboot). There are two possible solutions and a workaround to this issue:

Possible Solutions:
    • Downgrade the BIOS version (to P89 v1.21).
    • The issue should not occur with kernel 3.10 OS. If it does occur, it is necessary to downgrade the BIOS.
Workaround:

Hard Reboot through the Server, or power cycle via the iLO.


For HP ProLiant Gen10 Servers:

  1. Do these modifications in the BIOS settings:

    Setting Feature Required modifications
    Boot Options Boot Mode
    1. Set the default to Legacy BIOS boot (to disable UEFI)
    2. Reboot
      BIOS/Platform Configuration Process Options
      (Located in System Configuration -> BIOS/Platform Configuration (RBSU) -> Processor Options
      1. Set HT to Disabled
      2. Set Processor X2APIC Support to Disabled
      3. Reboot

      Notes
      :

        • The HP ProLiant DL380 Gen10 does not detect all USB devices, including different USB flash drives (regardless of their content). This is not a software issue.

        • If a bootable USB (with Check Point Gaia, CentOS, or any other OS) is not recognized by this server, try a different USB vendor.
    • Follow the instructions in sk98760 - Prerequisites for installing Security Management Server / Multi-Domain Security Management Server on Red Hat Enterprise Linux.

    Related Solutions:

    Give us Feedback
    Please rate this document
    [1=Worst,5=Best]
    Comment